- Homepage
- Brand
- Afam (28)
- Avon (19)
- Classic Bike Shop (26)
- Did (201)
- Domino (49)
- Helibars (45)
- Lsl (20)
- Ngk (28)
- Noco (27)
- Oem Suzuki (14)
- R & G Racing (12)
- Sc-motor (11)
- Scottoiler (19)
- Suzuki (1989)
- Suzuki (genuine Oe) (34)
- Suzuki Genuine Part (15)
- Suzuki Nos Oem (12)
- Unibat (17)
- Unibat, Shido (23)
- Wiseco (39)
- Other (2035)
- Intended Use
- Manufacturer
- To Fit Make
- To Fit Model
- See Full List Below (3)
- Ts 100 Ern (1979) (4)
- Ts 125 B (1977) (3)
- Ts 125 C (1978) (4)
- Ts 125 Er 1980-1981 (4)
- Ts 125 Erz (1982) (4)
- Ts 125 N (1979) (4)
- Ts 185 B (1977) (4)
- Ts 185 Ern (1979) (4)
- Ts 185 L (1974) (3)
- Ts 185 M (1975) (4)
- Ts 250 Er 1980-1981 (4)
- Ts 250 X 1986 (18)
- Ts 250 X 1986-1989 (4)
- Ts 50 Erk 1980-1983 (4)
- Ts 50 Kc (1978) (5)
- Ts 50 Kn (1979) (5)
- Ts 50 Xk 1991-1997 (4)
- Ts 80 Er 1981-1983 (3)
- Ts 80 X 1984-1987 (4)
- Other (4571)
- Vehicle Type
Suzuki ts 125 r tsr cylinder barrel jug (no power valves)
Suzuki ts 125 r barrel 1989-96, no power valves or valve covers, everything in the pictures is included. This was my spare barrel i had got ready to use if needed, i honed it out a while ago and left it covered in grease to stop rust so you will need to clean before use, can be used with a 56.50mm piston as it measures at 56.60mm at the top of the barrel and about the same at the skirt. I was going to just use it with a mitaka.
It is in nice condition overall and hasn't been bored out to death yet pistons go up to 2.50mm over so quite a lot of life left in this barrel 4 piston over sizes to go yet. I also done a bit of port finishing after honing so no rings will nip up, liner is in good condition no deep scratches or cracks. New studs for the power valve pulley the top one i used loctite because it felt a little looser than the other but is now solid and tight, it would have been ok i just wanted to be sure. I also used loctite on the top exhaust stud as again it felt looser than the other this is now also solid and will pull the exhaust in tight enough to not blow from the gasket. I think i skimmed the head it looks real nice and has cross hatch marks so im sure i did it a while ago.
Power valve slots look good no melting has taken place in there. I put new bolts all over the barrel.The temp sender is also almost brand new and in perfect condition. The power valve actuating arm seal looks ok condition also.
If you need any more info or pics just message me and i will sort you out. The item "Suzuki ts 125 r tsr cylinder barrel jug (no power valves)" is in sale since Thursday, February 22, 2018. This item is in the category "Vehicle Parts & Accessories\Motorcycle Parts\Other Motorcycle Parts".
The seller is "bubs-85" and is located in Worthing. This item can be shipped to United Kingdom, Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Australia, Russian federation, Canada, Brazil, Japan, New Zealand, Hong Kong, Norway, Indonesia, Malaysia, Mexico, Singapore, South Korea, Switzerland, Taiwan, Thailand, Saudi arabia, South africa, United arab emirates.- Brand: Suzuki
- Bundle Listing: No
- Classic Motorcycle Part: Yes